Are you planning on having an inground fibreglass pool constructed? In order for the installation process to go smoothly, you’ll need to hire a pool installation expert. However, there are some issues that your pool installation expert may face as well when installing your inground pool. A fibreglass pool is easier to install than other kinds of pools, but these issues can still affect your pool installation process. They include:
1. Roots
Before the installation process can start, you’ll need to ensure that all plants, as well as their roots, are removed from the installation area. You’ll want to make sure that you trace any roots you find, back as far as you can. You can go back nearly ten feet, from where you want your pool installed, and cut the root from there.
No trees should be within at least twenty feet of your pool. Trees that are large, with their roots, can affect your inground fibreglass pool after its construction. Unless you want the walls of your pool or the pool liner jutting out, keep trees away from the pool area.
With the help of an excavator, cutting through any roots you find, will be easy. If there are trees in the area, then they’ll need to be cut down. Their roots should also be poisoned as well.
2. Rocks
If there are large rocks in or near the pool area, then they’ll also need to be removed. An issue you may face is with finding machines that can effectively remove rocks of various sizes. You could also find boulders in your pool area. These can be manually lifted and moved far away from the pool area.
You could also need a hammer in order to break the boulder first before you can move it. In case you need to remove a boulder, you’ll probably find yourself with a dirt patch that will need to be filled out. This will help get the area to the same elevation as the ground around it.
It’s also possible, although slightly more expensive, to have rocks and boulders shaved.
3. Surface Run-off
The area you want to install your south brisbane fibreglass pool in can be lower than the general elevation of the area. If this is the case, then you should create a route that allows water to move around your pool. This prevents the water from going into your pool, or under it. You can get retaining walls installed, as well as french drains.
You could also get a trench dug next to your pool deck. Then, ensure that stone is used to fill up around 3/4ths of that trench. On top of this, add a drain pipe that’s perforated, and then add more stone. Then, it’s time for the trench to be backfilled. It should be filled till it’s just lower than the elevation of the area around it.
This way, if water does flow towards your pool, it will end up hitting the drainage section, before moving to the area that’s lower. You could also consider getting swales cut in the ground near the pool patio. This can also help you to better deal with surface run-off.
4. De-Watering Issues
Say the weather in your area is currently dry. Despite this, you keep finding water entering your fibreglass pool. If this is the case, then first ensure that the deep end of the pool is dug deeper. It should be at least two feet deeper than the general depth of your pool. Then, dig a trench around your pool. Start digging your trench from the deep end of your pool, moving towards the shallow end.
Then, you’ll need to ask a gravel company to provide you with stone, which you’ll use to fill the trench. First, use the stone to fill around 3/4ths of the trench. In case the soil in your area is more sandy, or if it’s loamy, then you should add a greater amount of gravel, to your trench. Should the soil be of tight clay, you’ll need less gravel, to ensure that the water stays flowing.
Then what?
Once you’ve added the gravel, it’s time to use a PVC pipe that’s flexible, to create the water’s conduit. Towards the end of the pipe that’s facing the pool, you should add check valves. Add grates as well, so that the pipe is able to run from the part of the pool that’s the lowest. It should flow along the pool’s bottom and enter the trench. The pipe can then be left in an area that has a pool pump. On the side of the pool pump that the discharge comes out of, another pipe should be attached.
Then the pool pump needs to be primed and turned on. Following this, the pool pump will pull out water from the underground, and out through the pipes.
5. High Water Table
If there’s a high water table around your pool area, then this can cause problems during the fibreglass pool installation process. These issues generally arise while deeper pools are being dug, such as a pool that’s eight feet deep. Even if the ground is dug around six feet or seven feet down, it’s possible for you to encounter a water table.
This water will need to be pumped out. Once it has been removed, the water won’t come back. Sometimes, however, the water might return just as soon as it is pumped out. When the water from the water table is being emptied out, it should be discharged at least fifty feet away from the pool. This way, the water won’t be recycled, as a result of which it could go back under your pool.
Conclusion
When you’re getting your fibreglass pool installed, there are some issues that you could face. Rocks will need to be removed, and roots will need to be thoroughly removed from the surrounding area. You may also deal with issues related to a high water table, in which case, you’ll need to de-water the area. Surface run-off could be an issue as well.
This guide discusses the most common issues you’re likely to face while installing an inground fibreglass pool. Learn also what the solutions to these problems are.